Home
About Us
Calendar
Fiero Documents
Merchandise
Tips
Links
Members
Message Board
Other Fiero Clubs
VIN Decoder
Speed Calculator
GFC Facebook Page
 

Author Topic: WTB: 4T60 Brackets  (Read 15831 times)

0 Members and 1 Guest are viewing this topic.

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
WTB: 4T60 Brackets
« on: April 23, 2015, 03:45:10 pm »
I'm looking for this bracket for the 4t60 tranny:



I've had no luck. Any help would be greatly appreciated.

I'm also looking for the Transmission to Engine bracket. I don't have a picture of it.
'88 Fiero Formula 2.8L v6

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,565
    • View Profile
    • Georgia Fiero Club
Re: WTB: 4T60 Brackets
« Reply #1 on: April 23, 2015, 06:31:06 pm »
Mike, can you tell us what vehicles used the 4T60 and where the brackets or mounts are located?  Maybe some of us could locate them in the pullapart yard if they are more than 10 years old. 
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: 4T60 Brackets
« Reply #2 on: April 23, 2015, 06:53:13 pm »
I've found thread on Pennocks. http://www.fiero.nl/cgi-bin/fiero/showThread.cgi?forum=Archive-000001&thread=20040223-2-042750

It shows some close up pictures. Don't know if this helps.





I'm reaching out to some salvage yards. Trying to get the parts ASAP, since I need these parts to finish the install. My Formula is in the shop waiting on me to get them. Any help is appreciated.
'88 Fiero Formula 2.8L v6

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: 4T60 Brackets
« Reply #3 on: April 23, 2015, 06:57:44 pm »
Here is another picture of a top down view.

'88 Fiero Formula 2.8L v6

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,565
    • View Profile
    • Georgia Fiero Club
Re: WTB: 4T60 Brackets
« Reply #4 on: April 23, 2015, 11:05:24 pm »
Try this website.   http://www.car-part.com/

It's what the junk yards use to locate parts that they don't have.  My neighbor works for a large yard in the Atlanta area and it's the site they use. 
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: 4T60 Brackets
« Reply #5 on: April 25, 2015, 05:19:38 am »
I've ordered some brackets. If they are the right ones, I'll post the part numbers for everyone in my other thread.
'88 Fiero Formula 2.8L v6

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,565
    • View Profile
    • Georgia Fiero Club
Re: WTB: 4T60 Brackets
« Reply #6 on: April 25, 2015, 06:45:01 am »
Did you order from the link above?  If you did, it would be good to know if they provided the right parts the first time.  If not for Fieros, it may come in handy for our other vehicles. 
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

Raydar

  • Paid Members
  • *****
  • Posts: 2,963
    • View Profile
Re: WTB: 4T60 Brackets
« Reply #7 on: April 25, 2015, 12:50:11 pm »
Did you order from the link above?  If you did, it would be good to know if they provided the right parts the first time.  If not for Fieros, it may come in handy for our other vehicles.

I have found that link to be quite useful. Found a 49K Fiero/Isuzu tranny, a few years back, for a project.
...

WV Mike

  • Full Member
  • ***
  • Posts: 155
    • View Profile
Re: WTB: 4T60 Brackets
« Reply #8 on: April 28, 2015, 04:10:57 pm »
The part isn't from the link above. For the transmission mount bracket pictured in my original post, the GM part number 22145828.

And, for the transmission to engine bracket, I am able to use the original bracket taking my dremel to two of the corners to make it work. May need to use a few spacers to align; but, that should be fine.
'88 Fiero Formula 2.8L v6