1
Club Events / SCCA Track Nights Events
« on: February 10, 2023, 08:10:05 am »
Come join us for hot laps around AMP in Dawsonville GA April 19th! Registration is through SCCA Track Nights @ tracknightinamerica.com
News:
We are updating the web site. Please be patient.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
6
Club Events / SCCA Track Nights
« on: May 15, 2022, 01:24:10 pm »
For those who want a little more of a driving challenge I invite you to attend a SCCA Track Night event! All you need is an approved SNELL 2010 or newer helmet and completed vehicle inspection form. Local events will be posted on calendar and is up to you to register through SCCA Track Nights.
7
Tech Tips, Tech Questions / Decklid Weatherstrip at Back Glass
« on: March 19, 2021, 02:03:01 pm »
What is anyone using for replacement weatherstrip on the decklid at back glass?
8
Club News / Fund Raisers
« on: September 24, 2019, 10:58:28 am »
This is our annual fund raiser for needy families is Oakwood GA, would love a good Fiero Club turnout in support of this event. Also if we have enough cars i may be able to reserve a Fiero section and maybe out do those over achievers Corvette Club! Lol!
9
Tech Tips, Tech Questions / Pulling Transmission
« on: January 18, 2019, 10:43:10 am »
Question to the Fiero experts & gear heads,
1) my 86 GT had a recent 3800 swap with the factory Muncie 4 speed, i noticed the clutch starting to slip recently on hard runs, clutch is a “Spec 3+” less than 10k miles on it, there is oil dripping out of bell housing, engine side of flywheel is clean, engine oil is still clear as well as transaxle oil, the oil dripping out is black. My guess is the input shaft seal is bad and getting oil on clutch. Am I on the right track? And if it is that seal is this typical failure or should i be looking at a more serious trans issue?
2) I understand that i’ll need to pull the trans regardless and it will be my first attempt at it, I was reading up on how to’s and came across a forum on how to do a half cradle drop just to pull trans out, has anyone done this? The reason i ask is that i dont have any heavy lifts to raise my Fiero high enough to drop the entire cradle.
Thx,
1) my 86 GT had a recent 3800 swap with the factory Muncie 4 speed, i noticed the clutch starting to slip recently on hard runs, clutch is a “Spec 3+” less than 10k miles on it, there is oil dripping out of bell housing, engine side of flywheel is clean, engine oil is still clear as well as transaxle oil, the oil dripping out is black. My guess is the input shaft seal is bad and getting oil on clutch. Am I on the right track? And if it is that seal is this typical failure or should i be looking at a more serious trans issue?
2) I understand that i’ll need to pull the trans regardless and it will be my first attempt at it, I was reading up on how to’s and came across a forum on how to do a half cradle drop just to pull trans out, has anyone done this? The reason i ask is that i dont have any heavy lifts to raise my Fiero high enough to drop the entire cradle.
Thx,
10
Tech Tips, Tech Questions / Clutch Problems
« on: July 29, 2018, 10:56:14 pm »
Hey folks,
I’ve replaced the clutch pedal, master cylinder “banjo string loop up”, slave cylinder which was leaking and bled the lines several times and it still wont release the clutch fully on my 85 GT! The slave cylinder seems to be traveling full extension which i believe should be 1.2 inches but haven’t been able to measure due to heat shield blocking. All replacement parts are from Fiero Store. What am i missing?
Thx
I’ve replaced the clutch pedal, master cylinder “banjo string loop up”, slave cylinder which was leaking and bled the lines several times and it still wont release the clutch fully on my 85 GT! The slave cylinder seems to be traveling full extension which i believe should be 1.2 inches but haven’t been able to measure due to heat shield blocking. All replacement parts are from Fiero Store. What am i missing?
Thx
Pages: [1]