Home
About Us
Calendar
Fiero Documents
Merchandise
Tips
Links
Members
Message Board
Other Fiero Clubs
VIN Decoder
Speed Calculator
GFC Facebook Page
 
« previous next »
Pages: [1]

Author Topic: Plastic hood latch cover  (Read 13705 times)

0 Members and 1 Guest are viewing this topic.

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Plastic hood latch cover
« on: February 11, 2021, 07:58:37 pm »
The plastic hood latch cover is in need of some restoration.  Around the screw holes, the plastic could be better.  Anyone every tried to get the plastic back to how it should be?
Logged

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,589
    • View Profile
    • Georgia Fiero Club
Re: Plastic hood latch cover
« Reply #1 on: February 11, 2021, 08:13:06 pm »
You're speaking of the plastic cowl cover that fits around the exterior hood latch?  I have seen cowl covers that were in pristine condition, except for the area immediately in front of the screened portion and that area was warped and stood up from making contat with the body.  It might be possible to use a heat gun sparingly and get it to reform around the latch and also at the vent inlet area. 
Logged
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Plastic hood latch cover
« Reply #2 on: February 11, 2021, 08:14:04 pm »
There is some missing thickness in the plastic around the screw holes.
Logged

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,589
    • View Profile
    • Georgia Fiero Club
Re: Plastic hood latch cover
« Reply #3 on: February 12, 2021, 09:23:19 am »
Can you post some pictures?  They might give us some suggestion ideas.
Logged
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Plastic hood latch cover
« Reply #4 on: February 12, 2021, 07:11:57 pm »
Here is a picture:


The two screw holes on the left seem to be in rather poor condition.  I'm not sure, but that notch at the top seems to be broken.

I already fixed the two tabs.
Logged

Fierofool

  • Global Moderator
  • *****
  • Posts: 10,589
    • View Profile
    • Georgia Fiero Club
Re: Plastic hood latch cover
« Reply #5 on: February 12, 2021, 09:12:15 pm »
If you could find some nylon washers like used on the weather seals at each end of the door glass might suffice in strengthening it.  They would spread the load on the thin plastic.
Logged
There are three kinds of men:

1.    The ones that learn by reading.
2.    The few who learn by observation.
3.    The rest of them have to pee on the electric fence and find out for themselves.    Will Rogers

GTRS Fiero

  • Hero Member
  • *****
  • Posts: 12,510
  • It is what it is.
    • View Profile
Re: Plastic hood latch cover
« Reply #6 on: February 12, 2021, 09:14:19 pm »
Hmmm.  I am going to try something different.
Logged
Pages: [1]
« previous next »